上水口环形吹氩对中间包内渣眼形成的影响

 中间包上水口环形吹氩可以在塞棒周围形成清洗钢液的环形气幕，同时部分氩气泡随钢液进入上水口内，可以减少非金属夹杂物在水口内壁的黏附，起到防止水口堵塞的作用。然而，不合理的吹氩量会导致中间包内液面渣层受过强的气液羽流冲击而形成渣眼，使得钢液裸露并发生二次氧化，严重影响铸坯质量。采用标准 k ε 湍流模型研究中间包内流体流动，采用DPM模型和VOF模型耦合方法，研究上水口环形吹氩条件下渣眼的形成及演化规律。结果表明，上水口环形吹氩在塞棒周围形成较强的上升流，塞棒上部邻近区域存在多个涡流区；在钢液涡流的影响下，中间包液渣下层远离塞棒区域，上层向塞棒区域迁移；随着吹氩量的增大，平均湍动能增大，塞棒附近钢液速度逐渐增大，钢渣界面钢液速度先增大后减小，渣眼边缘钢液速度先增大后减小然后再增大，速度与垂直方向夹角逐渐减小；增大吹氩量，中间包熔池液面形成以塞棒为中心的渣眼，渣眼面积逐渐增大。试验条件下不产生渣眼的临界吹氩量为4.2 L/min，对应的钢渣界面最大速度为0.247 m/s，与垂直方向夹角为70°。     

Displacement bound of beam‐column with time‐dependent boundary constraints

Abstract

A simplified explicit formula for the displacement bounds of the beam‐column subjected to time‐dependent boundary constraints is proposed. The formula is derived by means of removing time dependence from the boundary conditions. The proposed bounds provide a quick estimation of the displacements for problems with complex loading conditions.     

昭通晚清民国时期彝族上层社会建筑概貌及分析

昭通是彝族的重要发祥地之一，彝族自古以来对昭通的政治、经济、文化影响极大，彝族上层社会的建筑为研究昭通彝族文化和历史的变迁提供了重要的实物证据。文章通过昭通晚清民国时期彝族上层社会建筑的调查，对典型建筑案例进行了概述，分析了昭通晚清民国时期彝族上层社会的建筑特征和建筑文化，希望地方历史建筑的保护能够得到加强和重视。     

Characterization of ternary phase diagrams by means of thermal and rheological analyses

Context: Mixtures made of oil, water and surfactants give rise to a wide range of structure with different characteristics and phase manifestations.

Objective: Aim of this paper is to build up and understand the phase diagram of a model ternary system (Water, Polysorbate 80 and isopropyl myristate) by the use of common techniques such as thermal analysis and rheology, in comparison with visual assessment and polarized light microscopy.

Methods: Different ternary systems were prepared and analyzed by means of DSC and rheology in order to highlight the state of water (free, interphasal, bound water) and the samples structural characteristics.

Results: The resultant phase diagram is divided into four different zones. Bound water zone is predominant at elevated surfactant/oil ratios, while as the surfactant/oil ratio decreases, DSC reveals the presence of free water. Interphasal water prevails at intermediate water and surfactant content which corresponds with gels systems. Mechanical spectra allow to discern between cubic (true gel) and lamellar mesophases (weak gel), while flow curves allow to distinguish among microemulsions, emulsions or lamellar mesophases.

Discussion: A deeper characterization of a model ternary phase diagram is possible, with respect to the simple visual inspection, by the use of thermal analysis and rheology. The state of water molecules and the viscoelastic characteristics of the system allow to obtain important structural considerations.

Conclusions: In conclusion, the knowledge of the state of water and of the viscoelastic characteristics of the systems allow a deeper understanding of the structural features of the ternary phase diagram.     

Capacity allocation problem in flexible manufacturing systems: branch and bound based approaches

This study considers an operation assignment and capacity allocation problem that arises in flexible manufacturing systems. The machines have limited time and tool magazine capacities and the available tools are limited. Our objective is to maximise total weight of assigned operations. We develop a branch and bound algorithm that finds the optimal solutions and a beam search algorithm that finds high quality solutions in polynomial time.     

一类Hilfer型分数阶微分方程解的存在和唯一性

用Banach不动点定理和上下解方法研究了α(1<α <2)阶数和β(0≤β ≤1)类型Hilfer分数阶微分方程的解,给出了方程解的存在和唯一性,并通过例证验证了本文所得结果的有效性.     

Development of high performance amine functionalized zeolitic imidazolate framework (ZIF-8)/cellulose triacetate mixed matrix membranes for CO2/CH4 separation

High cost and complex fabrication process of inorganic membranes and lower position of pristine polymeric membranes in the Robeson upper bound curve urged the researchers to develop mixed matrix membranes (MMMs). Cellulose acetate being most commercially used polymer, dominates the market of CO₂ separation mainly because of low cost and environmental friendly resource. In the present study, MMMs consists of amine functionalized zeolitic imidazolate framework (NH₂-ZIF-8) and cellulose triacetate were fabricated for the first time. NH₂-ZIF-8 was used as a filler because the pore size of ZIF-8 is between the kinetic diameter of separating gases (CO₂ and CH₄). Moreover,  NH₂ group attached on the surface of ZIF-8 has affinity with condensable gases like CO₂. Morphology, crystallinity, tensile strength and functional groups of fabricated membranes were investigated using different analytical techniques. Results revealed that the increase of feed pressure has increased CO₂ permeability and decreased permselectivity. However, improvements in gas separation performance were observed with the addition of nanofiller. Best position in Robeson's upper bound curve at 4 bar was obtained with 10 wt% loading with CO₂ permeability and CO₂/CH₄ permselectivity of 218 barrer and 13.84, respectively. The improvement in the gas separation performance with loading is attributed to the increased diffusion coefficients as well as solubility coefficients, which was increased to 33% and 3.8%, respectively.     

基于分支定界法的相控阵雷达事件调度算法

为解决相控阵雷达事件调度问题中调度成功率、时间偏移率与算法时效性三者之间的矛盾，本文提出一种基于分支定界法的调度算法；该算法首先在现有调度结果上调取所有可执行事件，即获得若干"节点"，多步递推后由多"层"节点形成若干条备选"分支"，扩大解空间范围，提高算法性能；然后通过"删减"操作删减掉收益较低分支，将解空间控制在一适当范围内，减小搜索盲目性，降低算法计算量.仿真实验表明，与基于综合优先级算法的调度结果相比，利用本文算法调度时调度成功率提升了52%；与基于时间指针算法的调度结果相比，本身算法时间偏移率降低了61%；与基于遗传算法的调度结果相比，本文算法调度耗时仅为前者1~2%.     

On the use of calibration sensors in source localization using TDOA and FDOA measurements

The accuracy of a source location estimate is very sensitive to the presence of the random noise in the known sensor positions. This paper investigates the use of calibration sensors, each of which is capable of broadcasting calibration signals to other sensors as well as receiving the signals from the source and other calibration sensors, to reduce the loss in the source localization accuracy due to uncertainties in sensor positions. We begin the study with deriving the Cramer–Rao lower bound (CRLB) for source localization using time difference of arrival (TDOA) and frequency difference of arrival (FDOA) measurements when a single calibration sensor is available. The obtained CRLB result is then extended to the more general case with multiple calibration sensors. The performance improvement due to the use of calibration sensors is established analytically. We then propose a closed-form algorithm that can explore efficiently the calibration sensors to improve the source localization accuracy when the sensor positions are subject to random errors. We prove analytically that the newly developed localization method attains the CRLB accuracy under some mild approximations. Simulations verify the theoretical developments.     

Improved results on delay-interval-dependent robust stability criteria for uncertain neutral-type systems with time-varying delays

In this paper, we consider the problem of delay-interval-dependent robust stability and stabilization of a class of linear uncertain neutral-type systems with time-varying delay. By constructing a candidate Lyapunov–Krasovskii functional (LKF), that takes into account the delay-range information appropriately, less conservative robust stability criteria are proposed in terms of linear matrix inequalities (LMIs) to compute the maximum allowable upper bounds (MAUB) for the delay-interval within which the uncertain neutral-type system under consideration remains asymptotically stable. The verifiable stabilizability conditions and memoryless state feedback control design are stated. Finally, numerical examples are also designated to demonstrate the effectiveness and reduced conservatism of the developed results.